CSA O86 (CSA O86:19), verified in limit states design (LSD) under the National Building Code of Canada

Design Rothoblaas Screws to CSA O86

SPEC Toolbox designs Rotho Blaas self-tapping wood screws to CSA O86 under the National Building Code of Canada, in limit states design, using the specified withdrawal, head pull-through and lateral design values of ICC-ES ELC-4645. The integration covers twenty-one Rotho Blaas screw families - the partially threaded HBS, HBS PLATE, TBS, KKF and SHS and the fully threaded LBS, LBSH, VGZ, VGS and VGS PLATE, in zinc-plated, EVO-coated and stainless versions - for wood-to-wood and steel-to-wood connections in sawn lumber, glulam and CLT.

Start Designing for Free → Back to Rothoblaas → ICC-ES ELC-4645 (ICC-ES Listing Report for Canada)

Engineer guide

Designing Rothoblaas screws to CSA O86

Rotho Blaas (Rotho Blaas S.R.L., Cortaccia, Italy) manufactures self-tapping wood screws for timber construction. In Canada they are recognized under ICC-ES ELC-4645, an ICC-ES Listing Report confirming that the screws conform to Clauses 12.6 and 12.11 of CSA O86. SPEC Toolbox designs the connections to CSA O86, in limit states design, using the design values published in that listing.

Product range

The integration covers twenty-one Rotho Blaas screw families, all self-drilling dowel-type fasteners that install without a lead hole.

Partially threaded

  • HBS and HBS EVO (countersunk head with milling ribs), HBS PLATE, HBS PLATE EVO and HBS PLATE A4 (washer head for steel plates), TBS, TBS EVO, TBS MAX and TBS FRAME (large washer head), and the stainless KKF and SHS (martensitic Type 410).

Fully threaded

  • LBS, LBS EVO, LBSH and LBSH EVO (round head, for steel plates), VGZ and VGZ EVO (cylindrical head), VGS, VGS EVO and VGS A4 (countersunk or hexagonal head), and VGS PLATE (countersunk hexagonal washer head for steel plates, 11 mm, black zinc plated).

Carbon-steel screws are zinc plated, with or without a coloured E-coating, or carry the proprietary multi-layer EVO or EVO C5 corrosion-resistant coating; the A4 versions are austenitic stainless Type 316. The listed screws run from 3.5 to 13 mm in nominal diameter, with the longest VGZ and VGS sizes reaching 1500 mm, and the countersunk screws pair with the HUS countersunk washers and the VGS with the VGU 45 degree washers.

Compatibility

In the Canadian scope the Rotho Blaas screws support:

  • Wood-to-wood and steel-to-wood connections.
  • Sawn lumber, structural glued-laminated timber and cross-laminated timber, with an assigned specific gravity from 0.35 to 0.55 per CSA O86 Table A.11.
  • Withdrawal, head pull-through and lateral loading, in limit states design.
  • Installation with or without predrilling up to a specific gravity of 0.55, and predrilled above it.
  • Dry service, with sawn lumber at a moisture content of 19 percent or less.

What's distinctive

  • A Canadian listing derived from the US test data. ELC-4645 recognises the screws as alternative dowel-type self-drilling fasteners under the note to Clause 12.6.1.1 of CSA O86, which allows reliance on test results to ICC-ES AC233. The same testing that supports the US report ESR-4645 is converted, with an engineering analysis, into limit states design values for Canada.
  • Specified withdrawal values by specific gravity. The listing tabulates the specified withdrawal resistance per millimetre of thread for each screw at specific gravities of 0.35, 0.42, 0.49 and 0.55 – for example 162.91 N/mm for the 13 mm VGZ and VGS at 0.55 – so the withdrawal resistance follows the assigned relative density of the actual member.
  • Placement rules that change with density and predrilling. Minimum end, edge and spacing distances are given separately for self-drilled screws in lighter species (specific gravity up to 0.49), self-drilled screws in denser species, and predrilled holes, with the predrilled case allowing much closer spacing.
  • EVO coating carried at full design value. The tabulated values for zinc-plated carbon-steel screws apply equally to the EVO, EVO C5 and E-coated versions, so the corrosion-resistant coating can be specified without a reduction in design capacity.

In the platform

The Rotho Blaas screws are available in the SPEC Toolbox Screw Design module, worked to CSA O86:19 in limit states design, in metric units:

  • Members: the supported and supporting members, with the specific gravity G of each member entered directly.
  • Connection and Screw: the member type (wood-to-wood or steel-to-wood), the thread type (partially or fully threaded), the Rotho Blaas screw family and the screw type by diameter and length, with smart screw lengths and a pre-drilling toggle for each member.
  • Loading and Design: the applied withdrawal and lateral loads and the design settings.

The calculator reports a Summary with a Geometry Check, the Axial Capacity, the Shear Capacity and a Brittle Failure check. The axial result gives the factored withdrawal resistance of the point-side member, the factored head pull-through resistance of the head-side member and the governing factored withdrawal resistance of the connection; the shear result gives the factored lateral resistance for loading at an angle to the grain; and the brittle failure check gives the factored row shear, group tear-out and splitting resistances. Because CSA O86 gives no guidance for combined withdrawal and lateral loading, each applied load is checked against its own resistance, and the wood side member must be at least 14 mm thick.

Design codes

Design follows CSA O86 (CSA O86:19, Engineering Design in Wood) in limit states design, under the National Building Code of Canada. ICC-ES ELC-4645 confirms conformance with Clauses 12.6 and 12.11 of CSA O86 (2019 and 2014), as referenced by the NBC 2020 and 2015. The factored withdrawal resistance is determined in accordance with Clause 12.6.6.1, using the specified withdrawal resistance Yw of the listing for the assigned specific gravity of the member, with the screw tip excluded from the embedded length; for fully threaded screws the head pull-through resistance is based on the withdrawal resistance of the thread embedded in the side member, and for the HBS and TBS families the specified head pull-through value fpt is tabulated directly. The factored lateral resistance is determined in accordance with Clause 12.6.5, using the bending yield strength Fy of the listing, with the unthreaded shank diameter for partially threaded screws and the root diameter for fully threaded screws, a minimum penetration into the main member of eight times the outside thread diameter, and a minimum side member thickness per Clause 12.6.4.1. The tabulated values apply to standard-term loading and dry service, and are adjusted with the CSA O86 modification factors for other conditions. Wood members must carry an assigned specific gravity from CSA O86 Table A.11, sawn lumber must have a moisture content of 19 percent or less, and engineered wood products other than sawn lumber, glulam and CLT are outside the scope of the listing.

More from this partner

Other Rothoblaas Integrations

Bracket connection design icon
Brackets

Brackets

Eurocode 5 (EN 1995-1-1) Calculator →
Screw connection design icon
Screws

Screws

ETA-11/0030 Calculator →
Screw connection design icon
Screws

Screws

The NDS (ANSI/AWC NDS) under the IBC / IRC Calculator →
In their words

Why Rothoblaas builds on SPEC

“We decided to support SPEC Toolbox because, like Rothoblaas, they are a company that supports the industry with passion and expertise. That combination of passion and know-how is what makes SPEC Toolbox such a great partner.”

Luca Sestigiani, Technical Director – Rothoblaas

Frequently asked questions

Design With Rothoblaas

How current is the Rothoblaas screw data in SPEC Toolbox?

It is written against ICC-ES ELC-4645, reissued July 2025 and revised December 2025 (subject to renewal July 2026). Values are re-checked against the listing at its next reissue before the integrated data changes.

Which Rothoblaas screws are part of the Canadian integration?

Twenty-one families: the partially threaded HBS, HBS EVO, HBS PLATE, HBS PLATE EVO, HBS PLATE A4, TBS, TBS EVO, TBS MAX, TBS FRAME, KKF and SHS, and the fully threaded LBS, LBS EVO, LBSH, LBSH EVO, VGZ, VGZ EVO, VGS, VGS EVO, VGS A4 and VGS PLATE.

What can the screws be used in?

Wood-to-wood and steel-to-wood connections in sawn lumber, structural glued-laminated timber and cross-laminated timber with an assigned specific gravity from 0.35 to 0.55, in dry service. Engineered wood products other than these are outside the scope of the listing.

Do the screws need predrilling?

The screws are self-drilling. Predrilling is optional for members with an assigned specific gravity of 0.55 or less and required above 0.55, with the drill hole diameter set by the screw size and the specific gravity. Predrilled holes allow considerably closer end, edge and spacing distances.

What is an ICC-ES Listing Report for Canada?

ELC-4645 is an ICC-ES Listing Report confirming that the Rotho Blaas screws conform to Clauses 12.6 and 12.11 of CSA O86. It is the Canadian counterpart of the US evaluation report ESR-4645, converting the same AC233 test data into limit states design values.

FOR ENGINEERSStart designing now

Free, browser-based, no download. Design any certified connection into your real materials in seconds.

Start Designing For Free →
FOR SUPPLIERSBecome a partner

Get your products in front of every engineer specifying on the platform — at the point of design.

Get Your Products Specified →
Close Menu